Sections

Adhesives

French

German

Italian

Spanish

  • Fletch-Tite™ Platinum

    Download TIFF(RGB, 300 DPI, 8089.16kB)

    Download JPG(RGB, 300 DPI, 251.58kB)

    .

    Provides an extremely tough, durable bond, remains flexible and water repellent. Platinum provides you with an incredible bond with cedar, fiberglass, aluminum, or carbon shafts. Available in ¾ oz. tube, 2 oz. tube (while supplies last), 1/2 pint,  pint, quart, and gallon.

    *More Information
    Vane Clamp Time: 2-3 Minutes
    Feather Clamp Time: 15-20 Minutes
    Directions for Fletching: Apply thin bead to vane or feather base. Place fletching. Make sure base fully contacts shaft.
    Directions for Nocks: Apply small amount to nock. Install nock and rotate one full turn.

    Back to Top

  • Platinum & Fletch-Tite® Thinners

    Download TIFF(RGB, 300 DPI, 5946.81kB)

    Download JPG(RGB, 300 DPI, 289.77kB)

    .

    Thinners are engineered to work specifically with Platinum or Fletch-Tite Adhesives. Available in pint, quart and gallon.

    Back to Top

  • Quantum XT

    Download TIFF(RGB, 300 DPI, 7474.39kB)

    Download JPG(RGB, 300 DPI, 255.81kB)

    .

    Instantly bonds nocks, vanes, feathers and inserts. A "flex" agent makes Quantum extremely impact resistant.

    *More Information
    Vane and Feather Clamp Time: 8 seconds
    Torsional Strength: 3750 psi
    Directions for Fletching: Apply thin bead to vane or feather base. Place fletching. Make sure base fully contacts shaft.
    Directions for Inserts: Apply small amount to nock. Install nock and rotate one full turn.

    Back to Top

  • Instant Gel

    Download TIFF(RGB, 300 DPI, 9366.12kB)

    Download JPG(RGB, 300 DPI, 247.64kB)

    .

    Quick set cement in an easy to use gel for fletching vanes and feathers to aluminum, carbon, fiberglass and wood shafts. Available in 3 gram and 20 gram.

    *More Information
    Vane and Feather Clamp Time: 25 seconds
    Torsional Strength: 2700 psi
    Directions for Fletching: Apply thin bead to vane or feather base. Place fletching. Make sure base fully contacts shaft.
    (Do not use on inserts)

    Back to Top

  • Feather Fletching Tape

    Download TIFF(RGB, 300 DPI, 8691.59kB)

    Download JPG(RGB, 300 DPI, 313.49kB)

    .

    Easily applied, creates a strong ad reliable bond on contact. Will fletch over 3 1/2 dozen arrows.

    *More Information
    Feather Clamp Time: On contact
    Directions: Apply tape to feather quill. Trim with scissors, leave 1/8" overhang on each end. Remove tape backing. Press feather firmly onto arrow shaft. Make sure base fully contacts shaft.

    Back to Top

  • Dispenser Bottles

    Download TIFF(RGB, 300 DPI, kB)

    Download JPG(RGB, 300 DPI, kB)

    .

    For solvents or adhesives. Deluxe cap (white) for adhesives. Regular cap (red) for solvents.

    Back to Top

  • Ferr-L-Tite

    Download TIFF(RGB, 300 DPI, 303.19kB)

    Download JPG(RGB, 300 DPI, 303.19kB)

    .

    Hot melt cement, heat reversible. Tough elastic, waterproof bond that adheres points and inserts to aluminum or wood shafts. Stick or brick form.

    *More Informaiton
    Cure Time: 24 Hours
    Directions: Using an open flame heat adhesive. Apply to insert. Install insert and rotate one full turn. Wipe excess adhesive from shaft.

    Back to Top

  • PowerBond

    Download TIFF(RGB, 300 DPI, 198.08kB)

    Download JPG(RGB, 300 DPI, 198.08kB)

    .

    The ultimate insert and point adhesive. Works on all types of arrow shafts. An easy to use "One Step" adhesive. PowerBond does not get brittle under any condition or temperature. Heat reversible. (6 to 8 hour cure time).

    *More Information
    Cure Time: 6-8 Hours (full cure after 36 hours)
    Directions: Apply small amount to opposite sides of insert. Install insert and rotate one full turn. Wipe excess adhesive from shaft.
    Expands as is cures, moisture activated.
    Always maintain nitrogen bubble inside the bottle. Invert bottle and allow 2-3 seconds before squeezing out adhesive. If material begins to harden in bottle, add 1-2 drops of MINERAL SPIRITS and shake well. Wait 8 hrs. and repeat if necessary. DO NOT USE ANY OTHER SOLVENTS WITH THIS PRODUCT. Follow safety instructions listed on Mineral Spirits label.

    Back to Top

  • Quick Cure Epoxy

    Download TIFF(RGB, 300 DPI, 307.62kB)

    Download JPG(RGB, 300 DPI, 307.62kB)

    .

    A shock resistant, extra fast set that permanently bonds points or inserts to all types of shafts.

    *More Information
    Cure Time:     5 minutes (full cure after 24 hours)
    Directions: Mix 2 parts together and apply to insert. Install insert and rotate one full turn. Wipe excess adhesive from shaft.
    Quick Cure Epoxy has a shelf life of 2 years from manufacture date.

    Back to Top