Sections

Accessories

  • Bowstring Waxes

    Dry bowstring fibers tend to vibrate against each other when the bow is fired, thus wearing the fibers out prematurely and weakening the bowstring. Proper application of a good formula wax can extend the life of a bowstring many times over.  Always be sure to include areas of the string that are served.  This helps to keep the bowstring from moving inside the serving, minimizing wear.


    Xccelerator Wax – A revolutionary Wear Reduction Wax.  An all natural based string wax and conditioner that greatly reduces friction and abrasion typically found with cable slides, wheels and rollers.  Lubricates & rejuvenates your bowstring.  Water resistant and scent free.  Comes in a convenient, pocket sized retactable tube.

    1. Rotate tube base, bringing wax up.
    2. Apply liberally to the bowstring fibers.
    3. Rub wax into the bowstring fibers and servings. As wax warms, it melts into the fibers. 
    4. This should be done at the first indication of dryness in string fibers. Helps to extend the life of a bowstring.

     

    Tex-Tite Bowstring Wax – Natural based bowstring wax for all bowstrings. To apply:

    1. Push wax up from the bottom of the tube.
    2. Apply liberally to the bowstring fibers.
    3. Rub wax into the bowstring fibers and servings. As wax warms, it melts into the fibers.
    4. This should be done at the first indication of dryness in string fibers. Helps to extend the life of a bowstring.

    Provides a "tacky", durable coating when cooled.

     

    Seal-Tite Bowstring Wax – A silicone based bowstring wax. Seal-Tite lubricates the surface of the bowstring extending the life of the string and reducing the friction of the fibers during shooting. To apply:

    1. Push up from the bottom of the tube.
    2. Apply liberally to the bowstring fibers.
    3. Rub wax into the bowstring fibers and servings. As wax warms, it melts into the fibers.
    4. This should be done at the first indication of dryness in string fibers. Helps to extend the life of a bowstring.
    Provides a "sticky", durable coating when cooled. Seal-Tite remains soft and pliable in cold weather.
    Back to Top

  • Peep Sights

    Peep Sights
    Durable, high-impact plastic, lightweight with a slim profile.

    Target Peep Sight – Extra fine, 1/8" sight orifice. Alignment tube included.  We suggest simply tying the alignment tube to one of your cables.

    Hunter Peep Sight – Standard 3/8" sight orifice for low light conditions.  Alignment tube included.  We suggest simply tying the alignment tube to one of your cables.

    Back to Top

  • Field Points

    Z Point – Steel field point. Each Z Point holds extremely tight tolerances within ± 1 grain. The Z Point has a tapered design to ease shaft removal from all styles of foam targets. 2 diameters: 19/64" and 21/64" to match your shaft. 3 weight choices: 85, 100 & 125 grain.
    Back to Top

  • Bowstring Serving

    Serve-Tite String Server – Excellent for quick, tight center servings. Bohning Serve-Tite Server has two thread tension adjustments to assure consistently smooth and uniform string serving. Tension can be adjusted at the thread spool and the guide washer. This guarantees no overlapping winds as the server is revolved around the bowstring. A complete serving takes less than a minute to complete and the string can be served on a strong bow or while stretched between two posts.

    • A serving is started by holding a short piece of the serving thread on the bowstring and over wrapping it. The wrap is continued until the "V" notch of the server rests securely against the bowstring.
    • The server is revolved around the string. The server guides itself down the string laying a tight series of uniform wraps with no overlapping.
    • About ½" from the end of the serving, lay a loop of thread on the bowstring. Over wrap this to the end of the serving. Cut the serving thread from the server and run the thread end through the loop. With the loop, pull the serving thread back under itself and remove the looped end. Trim and finish the serving to your preference.
    When loading a new spool onto the Serve-Tite, special attention should be given to the loading procedure.
    1. Remove the wing nut holding the spool and insert new spool with thread coming off spool away from you.
    2. Run thread under the washer axle and pull thread up tightly between the guide tension washers.
    3. Run end of serving through the hole in the "V" notch of the server.
    4. Adjust the tension and washer so thread pulls off smoothly but with resistance.
    A spool of thread will do 40 or more servings. When the last layer of thread appears on the spool there is enough thread to complete one more serving. Bohning supplies both monofilament and nylon serving thread.

    No. 62 Braid Thread – Durable spectra and high tenacity polyester braided together allowing the spectra to ride on the outside for durability and the polyester gripping the bowstring.

    Back to Top

  • Miscellaneous

    Hunters Gear Belt - The perfect pack for all your hunting adventures. Two large zipper pockets for all your essentials, a water bottle holder, quick disconnect shoulder straps and an extra set of nylon straps for a bed roll or rain gear. Fully adjustable, padded, quick disconnect waist belt. Embroidered with the Bohning logo. Available in MossyOak Break-Up only. Add features such as the Bow Holster, Range Finder / Binocular Case and a Target Quiver.

    Bow Holster - Easy snap adjustment. Made of durable cordura. Available in MossyOak Break-Up only. Large pocket for single cam bows. A great addition to the Hunters Gear Belt

    Range Finder / Binocular Case - Made of durable cordura, the Range Finder / Binocular Case is padded to protect your optic gear. Has a quick-disconnect, adjustable flap and a snap on belt loop. A great addition to the Hunters Gear Belt.

    Wrist Sling - Fleece lined for comfort and silence. Fully adjustable. Provides a loose but secure grip on bow. Prevents lose of control after release. Improves accuracy by reducing strain on bow hand.

    Finger Tab - Sewn 2 piece. Leather backing with hair face to allow bowstring to release easier. Available in small, medium, large and extra large, right or left hand.

    3-Strap Arm Guard - Made of durable cordura. Approximately 7" in length.

    Grip-Tite Arrow Puller - Arrow puller with an amazing grip. Fits all shaft sizes. Made of new softer material . . . makes grip even stronger.

    Bow Grip / Camo Sight Window Pad - One moleskin camo pad and one black neoprene pad. Self-adhesive backing. Use one on your grip, sight window or any spot that needs camo, silencing or warmth. Cut to fit.

    Flight-Tite Arrow Rest - Flipper style arrow rest with or without spacer. Self-adhesive back. Comes in right or left hand. The Arrow Rest is also available with spacer.

    To apply the Arrow Spacer with Rest:

    • Attach arrow rest to clean, dry surface of "Bohning Spacer".
    • Insert long side of Allen Wrench into the locking screw. Insert stem of "Bohning Spacer" into the 5/16 - 24 tapped hole in the handle / riser.
    • Holding the spacer against riser, insert locking screw into the hole of the spacer stem. Tighten screw into the hole of the spacer stem. Tighten screw until spacer resists turning in other hand . . .approximately 5 turns.
    • Set nock point approximately ¼" above center.
    • Start tuning the bow by carefully shooting arrows off the arrow rest.
    If arrow rest needs to be moved out away from riser for better performance:
    • Retract screw until spacer moves freely in and out.
    • Holding spacer out the desired distance from the riser, reinsert screw and tighten with approximately 5 turns, as before.
    • Try shooting again. When position of spacer is desirable, using the short side of the Allen Wrench, continue turning lock screw until snug. DO NOT over tighten.
    Shaft-Tite Arrow Holder - Keeps arrows in shooting position until the arrow is drawn. As the bow is drawn, the arrow holder automatically releases from the arrow. Has a self-adhesive backing. Available for carbon and aluminum arrows and works for left or right hand.

    String Whiskers - Simply tie on to bowstring, cut and separate. Dampens noise and oscillations.

    Wind Check - A wind current finder. Great for testing wind currents too light to feel. Thermals occur which carry scent up and down based on the time of day. This product will detect these thermals. The bottle has a flip-top, which is easy to operate in one hand. Approximately 250 puffs per bottle. A gentle squeeze is all that is needed. Towards end of bottle, rotate sideways and squeeze. Powder is odorless. Do not inhale.

    Teflon Cable Slide - Silent, durable and self-lubricating cable slide. Made of 100% Teflon. Protects cables from premature wear.

    Kisser Button - Hunter Style kisser button. Provides a set anchor point every time you draw your bow. Make sure that it contacts the same place every time without having to move your head. Lightweight, durable and easy to use.

    Broadhead / Knife Sharpener - Simple to use and easy to carry sharpener. Rest arrow on a sturdy surface to provide a more consistent edge. Sharpen each blade of broadhead as needed starting at rear and sliding forward towards point. Always handle broadheads with care.

    Broadhead Wrench - Wrench will fit any combination of fixed blade broadheads. Keep turning wrench and fitting broadheads until broadhead seats evenly into wrench groves. Fit arrow threads to broadhead threads and screw arrow onto the broadhead by turning the arrow clockwise. Hold the broadhead and wrench still while continuing to turn arrow until it is tight.

    String Nocks - Available in Target, Cam and Hunter styles. String nocks mark the nocking point on a bowstring. Place string nocks onto string below the nocking point and crimp with nock pliers. Two string nocks should be placed at the top of the nocking point to prevent them from "threading" up the bowstring as the bow is shot.

    Pro-Class Fletching Jig - Perfect fletching every time. Quick-set magnetic clamp adjustment. Straight, Right Wing and Left Wing Helical.

    Clamp Release Tape - Teflon tape applied to fletching clamp. Prevents adhesive buildup.

    Alcohol Burner - Ideal for all hot melt adhesive applications. Use denatured alcohol. Denatured alcohol is a slow, even burning fuel that will give quick, clean results.

    Dri-Tite - A waterproof dressing formulated for feathers and dry flies. Eliminates flattening and loss of body. Will not stiffen or add weight. Dries instantly and will not harm finish. Flammable, contains mineral spirits and silicone.

    Dispenser Bottle - For adhesive and solvents (thinner). Deluxe cap (white) for adhesives. Regular cap (red) for solvents.

    Feather Dri - Water repellent powder for feathers. Colorless, odorless and will not effect fletch adhesion.

    1. Sprinkle a small portion of the powder into the provided bag.
    2. Place the fletched arrow (feathers) into the bag, closing the end tightly around the shaft.
    3. Shake the bag and work powder into the feathers. Shake excess off and arrow is ready.
    It will not disturb the fletching bond unlike many solvent-bases, water-repellent coatings. Avoid inhaling powder. It is non-toxic, but may irritate lungs.

    Crossbow Bolt Fletching Adapter - Easily adapts the Pro-Class Fletching Jig to accept crossbow bolts.

    SSR Arrow Shaft Surface Cleaner - SSR is an environmentally safe, high strength cleaner designed to remove dirt, grease and other contaminates from arrow shaft surfaces. This powerful cleaner will enhance adhesion on aluminum, carbon and fiberglass surfaces when used properly.

    1. Add hot tap water to within 1 1/2" from the top of container. Replace cap and shake well. To avoid etching of aluminum or removal of patterns on the shaft, do not concentrate the cleaner by adding less water.
    2. Soak the end of the shaft to be fletched or painted for 5 to 7 minutes.
    3. Remove and rinse shafts thoroughly with hot running water.
    4. Allow to air dry. Do not wipe dry.
    Avoid touching the surface prior to fletching or painting. SSR is safe for the environment, contains no phosphates or VOC's and meets USDA specifications. Several dozen shafts may be cleaned with a single bottle of SSR, however the number will vary depending upon the amount of contamination on the shafts to be cleaned. We recommend replacing your SSR when the contents become discolored or dirty. Not for use on wood shafts.
    Back to Top